Hessian Tape Camoflage

[Whiterook]

I just learned of an interesting camouflage netting, "Hessian Tape", which was a type of netting that was very popular with Commonwealth armies during WWII. It differs from ordinary netting, such as that used by the Germans, in that it has attached to it many strips of material which hang down looking like strips of tape.

Expert model builder, Jaffe Lam, uses whatever he can find that simulates the look of netting, with one example being bandage gauze… I think the key is getting the square hole size as close as possible, but the good news is, you are goin* to be cutting the netting so that it becomes very ropey at most edges, and finely placing the “tape” into the holes that are left. You can see this pretty well in the image below…



I’d probably paint a lot of that tape and netting as much as possible first.



Done right, the effect is super cool!



Many photos of British armor during and right after Normandy have this netting. The most popular uses for this netting was wrapped around the turret, and draped over the gun barrel and front hull. However, other combinations and additions can be found also, depending on the crew of the vehicle.

The primary purpose of this netting, as it is with any camouflage, was to make the vehicle very difficult to make out from the rest of the terrain. In this respect, it was quite effective; the netting helped to break up the harsh edges of the vehicle and the long strips of material gave an appearance of leaves. When properly used in conjunction with the local foliage, the vehicle could be made to look as if it was just another bush or tree.

[Whiterook]

As with many effects we try to recreate in our model building, Artistic License is out friend! …and honestly, there don’t seem to be many reference shots of this camo to be found, so use your judgement on what would have been available and how it would have been produced in the field.

The following instructions (slightly adapted), outlined in Missing Links, are designed to be a guide and can be applied to various Allied vehicles, one simply has to adapt them to meet your particular needs.

To begin, your vehicle should be painted and weathered. Next, you should find some kind of commercially available netting such as the one offered by Verlinden…but as mentioned in the previous post, be creative with what you have at home or the local stores; but be especially mindful of how you color or paint the netting, as you don’t want any applied netting color to bleed out on your model!

First select the areas were you want to apply your netting. The turret is always the most complicated. Research has often shown that the netting was held on to the turret by small lengths of wire or string, and it was usually just draped over the barrel and hull; you can use this method to aid in securing your netting to your model. In the case of my Cromwell below, small 0.010 wire was attached to the four large turret lifting points. The wire around the turret was placed loosely from loop to loop.

With the wire in place, you now have something to secure your netting to. Cut your netting material into pieces that would best suit the areas you want to cover on your vehicle. What you will want to do is drape the netting over the turret wire. Remember less is more, you can always add more netting later if you fell the first layer is insufficient. Attempt to dry fit the pieces to make sure they are the size you want.

Next, create a mixture of white glue and water, about 50-50% of each. Lay out your pieces of netting on a flat smooth surface. Then, using a large soft brush dab the netting with the glue mixture. Pick up the netting and carefully lay it over you vehicle. The netting will have a tendency to bind up, so work slowly. If you have used a wire on the turret, drape the netting over the wire. Try to completly cover the wire while positioning the netting so it looks as natural as possible. Again use the photos as a guide to get a "realistic look". Remove any excess glue drips with a bit of tissue, and let the netting partially dry over night.

**Warning, if you allow the netting to completely dry, it will be very difficult to introduced the "Hessian Tape" strips later on.

Now it is time to create the "Hessian Tape""strips. I used Tamiya’s high quality modeling tape for this purpose. You could try ordinary masking tape, but I’m not sure what the results would be. Lay pieces of tape out on a small piece of glass or mirror, then proceed to cut it up into strips of various lengths. The width of each piece is dependent on your taste as well as the photos you are using. I have seen various widths being used in photos, therefore exact dimensions are not that important. It just has to look reasonable!

Next, remove each piece one by one with a pair of tweezers and place it on the netting in a random fashion, again photos are a big aid. Try to layer some pieces and don’t be afraid to have some strips overlap each other. Now, using your tweezers, lift up some of the partially dried netting and weave the ends of the strips into the netting. This will add to the layered effect. Finally, using a small brush, paint each of the strips with your white glue and water mixture.

Let this dry again until it is almost solid. Now you must cut new pieces of netting, smaller then before. What we want to achieve is a layered appearance to the "Hessian Tape" netting. Proceed as before, laying the netting over the first layer and wipe off any excess glue. With your tweezers, start lifting up some of the strips and weave then through the second layer of netting. You may also want to add some new strips to your netting at this point.

Painting

When everything has completely dried you can now proceed to painting the netting. I would recommend to use an airbrush with the finest tip setting . You want to try to paint only the netting, not your vehicle. I used Polly Scale, Railroad Tie Brown no.414329, mostly to differentiate the netting from the rest of the vehicle. You could also use various shades of green if you wish. Once your paint is dry, you can now proceed to dry brush and weather the netting to your taste. To aid in the appearance of the netting, it may be helpful to paint highlights on the strips to help them stand out. You may also have to go back and touch up any areas of overspays on your vehicle.

Conclusion

"Hessian Tape" netting is a great way to differentiate your model in a very realistic way. The extra depth and texture it gives your vehicle will, when properly executed, add that little something which will make your work stand out. My instructions above are only meant as a guide.

It’s a nicely laid out procedure, but again, use your imagination and discretion on making your own method that achieves the results you desire!

Model Boldly, my friends!

[Whiterook]

Another great example, from Ade Wild:

Quickie on hessian tape camouflage netting.
1. Materials: cotton net and decorating masking tape. Mark out and precut cut the tape to suit.
2. Work pointed tweezers between the net threads.
3. Grab the piece of cut masking tape, glue side up.
4. Fold the tape over and pinch with the tweezers to get a good fix. No need to be too tidy, the real thing was stitched in a similar fashion... And repeat.









An example of a test fit…







With paint…